Game Console Repair by Computer Doctors!
Head Office:
2669 Tungsten Ct
San Bernardino, CA 92408
(909) 991-7709
solution@computer-doctors.org
2669 Tungsten Ct
San Bernardino, CA 92408
(909) 991-7709
solution@computer-doctors.org
All rights reserved.
| Limited time offer: $45 per hour Coupon: XCF748 |
| Privacy Policy | Terms of Service | Computer Doctors Inland Empire | Computer Doctors Orange County | Computer Doctors Los Angeles |
| New Location: 1230 E. Washington Street, Suite P8 Colton, CA 92324 |
 |
 |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
We will try to explain why we fix better than Sony
and Microsoft:
A lot of people are asking what is reflowing or reballing?
Also they ask how does Computer Doctors fixes their
systems?
Well, let us explain what we do:
Reflowing is a process where we heat up the original chip
that fails on the board due to cold solder joints underneath
the chip. This is caused by heat, flexing and poor design.
Reheating the board and chip can caused the old solder to
become weaker, so we use flux to help it become stronger
but not back to its original state when you bought it new.
But the main problem is still there! Microsoft has to use
lead-free solder, which is required by USA law that any kid
toys must be lead free solder. This is where the poor
design comes into play.
Reflow expected life:
Xbox 360: 1 month to 1 year.
With a 90 day warranty.
Playstation 3: 4 months to 2 years.
With a 4 Month warranty
Wii: As of yet they do not require reflow
With a 4 Month warranty
Reballing is a process where we lift off the defective chip
and A) Repair it by put lead based solder (stronger solder)
on the chip and placing it back on the board or B)
Replacing the chip with a new / used chip (working) also by
putting lead based solder on it and placing it back on the
board. Why does this work 99.99% of the time? Because
the 99.99% of the time the main problem is either bad chip
or bad solder, so it just needs to be replaced and so that
the unit can be put back to new status. So what is the
0.01% chance this is where the pads on the board that hold
the solder in place are bad. This is rare and if this happens
it can not be repaired. The unit will need to be replaced.
Why is reballing better then sending it to Sony or Microsoft?
Let us explain. Microsoft & Sony will use lead free solder
will is very brittle and can break easy. We will use Lead
Based solder and will last much longer. Lead based solder
is used in high end equipment like USA satellites.
Reball expected life is:
Playstation 3: 2 to 5 years Plus
With a 1 year warranty. (Remember Sony only gives a 90
day warranty when they repair it)
Xbox 360: 1 to 3 years Plus!
With a 6 month warranty (Remember Microsoft only gives a
90 day warranty with them also!)
Wii: Reball is yet needed! Why? Because they do not use
overpowered chips on there system causing a lot of heat,
causing damage to the board or chip!
Why does Sony and Microsoft do this then? Because the
consumer demands high end graphics!
and Microsoft:
A lot of people are asking what is reflowing or reballing?
Also they ask how does Computer Doctors fixes their
systems?
Well, let us explain what we do:
Reflowing is a process where we heat up the original chip
that fails on the board due to cold solder joints underneath
the chip. This is caused by heat, flexing and poor design.
Reheating the board and chip can caused the old solder to
become weaker, so we use flux to help it become stronger
but not back to its original state when you bought it new.
But the main problem is still there! Microsoft has to use
lead-free solder, which is required by USA law that any kid
toys must be lead free solder. This is where the poor
design comes into play.
Reflow expected life:
Xbox 360: 1 month to 1 year.
With a 90 day warranty.
Playstation 3: 4 months to 2 years.
With a 4 Month warranty
Wii: As of yet they do not require reflow
With a 4 Month warranty
Reballing is a process where we lift off the defective chip
and A) Repair it by put lead based solder (stronger solder)
on the chip and placing it back on the board or B)
Replacing the chip with a new / used chip (working) also by
putting lead based solder on it and placing it back on the
board. Why does this work 99.99% of the time? Because
the 99.99% of the time the main problem is either bad chip
or bad solder, so it just needs to be replaced and so that
the unit can be put back to new status. So what is the
0.01% chance this is where the pads on the board that hold
the solder in place are bad. This is rare and if this happens
it can not be repaired. The unit will need to be replaced.
Why is reballing better then sending it to Sony or Microsoft?
Let us explain. Microsoft & Sony will use lead free solder
will is very brittle and can break easy. We will use Lead
Based solder and will last much longer. Lead based solder
is used in high end equipment like USA satellites.
Reball expected life is:
Playstation 3: 2 to 5 years Plus
With a 1 year warranty. (Remember Sony only gives a 90
day warranty when they repair it)
Xbox 360: 1 to 3 years Plus!
With a 6 month warranty (Remember Microsoft only gives a
90 day warranty with them also!)
Wii: Reball is yet needed! Why? Because they do not use
overpowered chips on there system causing a lot of heat,
causing damage to the board or chip!
Why does Sony and Microsoft do this then? Because the
consumer demands high end graphics!
